ITI Fitter Trade 50 MCQs Practice Questions – Part 2

ITI Fitter Trade 50 MCQs Practice Questions Part 2 | Fitter Multiple Choice Question Set Part 2 | Practice question for ITI students trade Fitter | Fitter trade MCQ for ITI trainees. (1.) Why breakage of teeth occur easily while sawing of thin walled work pieces and the start of cut? | (a.) Hand force is too big (b.) Cutting section is too short (c.) Coarse blade to be used (d.) Hand force acts only upon few teeth (2.) Which part of universal surface gauge is used to set scriber at required position exactly? (a.) Sung (b.) Guide pin (c.) Rocker arm (d.) Fine adjustment screw (3.) Which chisel used for squaring materials at the corners, joints? (a.) Flat chisel (b.) Cross cut chisel (c.) Diamond point chisel (d.) Half round nose chisels (4.) Convert one metre into millimetre. (a.) 10 mm (b.) 100 mm (c.) 1000 mm (d.) 10000 mm (5.) Name the property of metal which can be drawn into wire without rupture. (a.) Ductility (b.) Elasticity (c.) Malleability (d.) Tenacity (6.) Which caliper is used to find the centre of round bars? (a.) Inside caliper (b.) Jenny caliper (c.) Vernier caliper (d.) Outside caliper (7.) What is the spindle movement of one division of thimble with spindle thread of 0.5mm pitch? | (a.) 0.01 mm (b.) 0.10 mm (c.) 1.00 mm (d.) 10.0 mm (8.) Which chisel is used for cutting curved grooves? (a.) Flat chisel (b.) Web chisel (c.) Cross cut chisel (d.) Half round Nose Chisel (9.) What is the weight of hammer used for marking purpose? (a.) 200 grams (b.) 250 grams (c.) 300 grams (d.) 450 grams (10.) What is the effect of improper method of diagonal filing? (a.) Uneven surface finish (b.) Scratches on the surface (c.) Convexity on the surface (d.) Improper finish on surface (11.) Which chisel is used to remove excess metal from welded joint and castings? (a.) Flat chisel (b.) Web chisel (c.) Cross cut chisel (d.) Half round Nose Chisel (12.) Why chalk is applied on the face of the file? (a.) To reduce excessive pressure (b.) To increase chip removed rate (c.) To reduce penetration and pinning | (d.) To increase penetration and pinning (13.) What is the use of fine pitch hacksaw blades ? (a.) To cut soft metal (b.) To cut high speed steel (c.) To cut high carbon steel (d.) To cut conduit and other thin tubes (14.) Calculate the tap drill size for M10 x 1.25. (a.) 8.8 mm (b.) 8.7 mm (c.) 8.75 mm (d.) 8.65 mm (15.) What is the use of feeler gauge? | (a.) Check the width (b.) Check the height (c.) Check the length (d.) Check the gap between the mating parts (16.) What operation is carried out in a gang drilling machine? | (a.) Idle operation (b.) Repeated operation of drilling (c.) Continuous milling operation (d.) Successive operation of drilling (17.) Which is an integral part of the stock in vernier bevel protractor? (a.) Disc (b.) Dial (c.) Blade (d.) Main scale (18.) Which file is used to make the job close to the finishing size? (a.) Single cut file (b.) Curved cut file (c.) Double cut file (d.) Second cut file (19.) Which file has the parallel edges throughout the length? (a.) Hand file (b.) Bastard file (c.) Rasp cut file (d.) Single cut file (20.) What is the material to manfacture bench vice? (a.) Tool steel | (b.) High carbon steel (c.) Cast iron (d.) Medium carbon stee (21.) Which marking media provide clear lines on machine finished surfaces? (a.) White wash (b.) Prussian blue (c.) Copper sulphate (d.) Cellulose lacquer (22.) What is the purpose of slots provided in the slotted angle plate? (a.) Job clamping (b.) Easy handling (c.) Reduce weight (d.) Better appearance (23.) Which caliper is used to mark the centre of round bar? (a.) Jenny caliper (b.) Inside caliper (c.) Firm joint caliper (d.) Outside caliper (24.) Which is used for filling narrow grooves and angles above 10Â°? (a.) Square file (b.) Half round file (c.) Triangular file (d.) Knife edge file (25.) Name the defect that causes the metal chips to clog between the teeth of file? (a.) File bite (b.) Warping of file (c.) Glazing of file (d.) None of these (26.) Which part of outside micrometer ensure a uniform pressure between the measuring surface? (a.) Anvil (b.) Thimble (c.) Spindle lock (d.) Ratchet stop (27.) What is the principle of micrometer? (a.) Sliding (b.) Screw and nut (c.) Rack and pinion (d.) Worm and worm wheel (28.) How the wide range of depth can be measured by depth micrometer? (a.) Lengthy sleeve (b.) Lengthy spindle (c.) Adjustable base (d.) Equipped with a set of extension rods (29.) Which part of the bevel protractor contact with the inclined surface while measuring? (a.) Dial (b.) Disc (c.) Blade (d.) Stock (30.) What happens if the vice handle is over tightened? (a.) Spindle damage (b.) Hard jaw damage (c.) Fixed jaw damage (d.) Movable jaw damage (31.) Which metal cutting saw is used to cut large cross section area? (a.) Power saw (b.) Contour saw (c.) Circular saw (d.) Horizontal band saw (32.) Why marking tables are made up of cast iron? (a.) Self lubricating (b.) Make more rigidity (c.) Maintain the accuracy (d.) Prevent thermal expansion (33.) Which file is used for manufacturing of dies and moulds? (a.) Rotary file (b.) Tinkers file (c.) Barrette file (d.) Rasp cut file (34.) What is the method of removing metal chips clogged between the teeth of files? (a.) Brush (b.) Wire brush (c.) Copper strip (d.) Chalk powder (35.) Which vice is used for holding small work that requires filing or drilling? (a.) Pin vice (b.) Pipe vice (c.) Hand vice (d.) Tool maker s vice (36.) Which hacksaw blade is used for cutting along curved lines? (a.) HSS blade (b.) All hard blade (c.) Flexible blade (d.) Diamond blade (37.) Which chisel is used for cutting keyways? (a.) Flat chisel (b.) Cross cut chisel (c.) Punching chisel (d.) Diamond point chisel (38.) What is the purpose of Crowning on the cutting edge of chisel? (a.) Prevent slipping of chisel (b.) Prevent digging of corners (c.) Allow chisel to move freely on straight line (d.) Allow cutting edge to penetrate into the work (39.) How to prevent the tool rubbing against the work surface in metal cutting process? (a.) Decrease lip angle (b.) Increased rake angle (c.) Increase clearance angle (d.) Decrease tool wedge angle (40.) Name the property of metal that withstand shock or impact? (a.) Tenacity (b.) Hardness (c.) Brittleness (d.) Toughness (41.) Which part is the measuring face fitted to the frame of outside micrometer? (a.) Anvil (b.) Barrel (c.) Spindle (d.) Ratchet stop (42.) How the drill chucks are held on the machine spindle? (a.) By arbor (b.) By sockets (c.) By sleeves (d.) By special clamp (43.) Which drilling machine, the spindle head is moved towards or away from the column? (a.) Pillar drilling machine (b.) Gang drilling machine (c.) Radial drilling machine | (d.) Sensitive bench drilling machine (44.) Which type of screw threads are rounded at the crest and root? (a.) B.A thread (b.) B.S.F thread (c.) B.S.W thread (d.) ACME thread (45.) What is the formula to calculate tap drill size? (a.) Tap drill size Major dia â€“ (2 x depth) (b.) Tap drill size Major dia + (2 x depth) (c.) Tap drill size Major dia â€“ (2 + depth) (d.) Tap drill size Major dia + (2 + depth) (46.) Which activity causes excessive wear and chattering of drill bit while drilling? (a.) Too fast feed rate (b.) Too slow feed rate (c.) More cutting speed (d.) Too slow spindle speed (47.) Which part of combination set is used to mark and check angle of 90Â° and 45Â°? (a.) Rule (b.) Centre head (c.) Square head (d.) Protractor head (48.) Why ribs are provided in the angle plate? (a.) Provide flatness (b.) Prevent distortion (c.) Provide squareness (d.) Support the machined surface (49.) How much carbon content of steel is forgeable? (a.) Up to 1.2 % (b.) Up to 1.7 % (c.) Up to 1.9 % (d.) Up to 2.1 % (50.) Which cutting fluid used for drilling in cast iron? (a.) Dry air jet (b.) Soluble oil (c.) Mineral oil (d.) Vegetable oil Previous QuestionNext Question Keywords :- ITI Mock , ITI Mock Test, ITI Mock Test NCVT, ITI Mock Test 2020, ITI Mock Test 2021, ITI Mock Test 2022, ITI Mock Test 1st Year, ITI Mock Test 2nd Year, ITI Mock Test PDF Download, ITI Test, ITI Test Paper, ITI Test Questions, ITI Test Book, ITI Test Paper in hindi, ITI Test 2020, ITI Test 2021, ITI Test 2022, ITI Questions Answers, ITI Questions & Answers, ITI Questions & Answers pdf, ITI Question Paper, ITI Questions pdf, ITI Question Paper PDF, ITI Questions Paper 2020, ITI Questions Paper 2021, ITI Questions Paper 2022, ITI Answer Key, ITI Paper Scheme, ITI Paper Date, ITI Paper 2020, ITI Paper 2021, ITI Paper 2022, ITI Previous Year Question Paper, ITI Previous Year Question Paper NCVT, ITI Previous Year Question Paper ED, ITI Previous Year Question Paper Engineering Drawing, ED, Workshop Calculations & Science, ITI Previous Year Question Paper Workshop Calculations & Science, ITI ED Book PDF, ITI ED Drawing, ITI ED Drawing Exaam Paper, ITI Jobs, ITI Form, ITI Form Online, ITI Online Form, ITI Online Form 2022, UP ITI, ITI Uttar Pradesh, ITI Haryana, ITI UK, ITI UttraKhand, UP ITI Result, Uk ITI Result, Haryana ITI Result, MP ITI Result, UP ITI Scholarship, Uk ITI Scholarship, Haryana ITI Scholarship, MP ITI Scholarship, UP ITI Merit List, Uk ITI Merit List, Haryana ITI Merit List, MP ITI Merit List, UP ITI Exam Date, Uk ITI Exam Date, Haryana ITI Exam Date, MP ITI Exam Date, UP ITI Updates, Uk ITI Updates, Haryana ITI Updates, MP ITI Updates, UP ITI Admission, Uk ITI Admission, Haryana ITI Admission, MP ITI Admission If you have any dought in any question. you can comment below, we will reply as soon as possible. and subscribe our Youtube channel & Telegram channel for more updates..

ITI Fitter Trade 50 MCQs Practice Questions – Part 2

Recent Posts

Daily Current Affairs Quiz: 21-December-2024

Daily Current Affairs Quiz: 20-December-2024

Daily Current Affairs Quiz: 19-December-2024

Daily Current Affairs Quiz: 18-December-2024

Daily Current Affairs Quiz: 17-December-2024

Daily Current Affairs Quiz: 16-December-2024

ITI Fitter Trade 50 MCQs Practice Questions – Part 2

Related Post

Recent Posts

Daily Current Affairs Quiz: 21-December-2024

Daily Current Affairs Quiz: 20-December-2024

Daily Current Affairs Quiz: 19-December-2024

Daily Current Affairs Quiz: 18-December-2024

Daily Current Affairs Quiz: 17-December-2024

Daily Current Affairs Quiz: 16-December-2024