ITI Fitter Trade 50 MCQs Practice Questions – Part 5

ITI Fitter Trade 50 MCQs Practice Questions Part 2 | Fitter Multiple Choice Question Set Part 2 | Practice question for ITI students trade Fitter | Fitter trade MCQ for ITI trainees. (1.) Which stake is used for making sharp bends? (a.) Funnel stake (b.) Hatchet stake (c.) Half moon stake (d.) Beak or bick iron (2.) Which flux is used for soldering tin sheets? (a.) Resin (b.) Paste (c.) Zinc chloride (d.) Ammonium chloride (3.) What is the seam used in sheet metal joint for roofing and panelling? (a.) Lap seam (b.) Double seam (c.) Zinc chloride (d.) Ammonium chloride (4.) What is rivet interference? (a.) Thickness of sheet (b.) Diameter of the rivet (c.) Length to form the head (d.) Total rivet length required for riveting (5.) How the distance of first rivet is determined from the side edge? (a.) 3 x dia of rivet (b.) 2 x dia of rivet (c.) 2.5 x dia of rivet (d.) 3.5 x dia of rivet (6.) What is the advantage of stakes in sheet metal work? (a.) Sharpening (b.) Supporting (c.) Rest of workpiece (d.) Protect the tool from damage (7.) Which tool is used to make fluid-tight joint by pressing the riveted edge plate? (a.) Dolly (b.) Drift (c.) Caulking tool (d.) Fullering tool (8.) Why allowance is required while making various types of hems and seams? (a.) To make good appearance (b.) To prevent damage to the edges (c.) To prevent over lapping at the seam (d.) Maintain correct size and improve the strength (9.) Which sheet metal is easiest to joint and solder? (a.) Tinned plate (b.) Lead (c.) Galvanised iron (d.) Stainless sheet (10.) Why precision instruments are made of invar steel? (a.) Durability (b.) Cheaper in cost (c.) Surface finishing is fine (d.) Least coefficient of expansion (11.) Why lime stone serves as flux added to the ore in the blast furnace? (a.) To form molter slag (b.) To supply the oxygen (c.) To burn the carbon in coke (d.) To increase the melting point of ore (12.) Which micrometer having provision of interchangeable anvils? (a.) Depth micrometer (b.) Inside micrometer (c.) Outside micrometer (d.) Screw thread micrometer (13.) Which factor determine the selection of wire in screw thread micrometer? (a.) Thread angle (b.) Type of thread and pitch (c.) Root and crest (d.) Major diameter (14.) What is measured with telescopic gauge? (a.) Depth (b.) External dimension (c.) Angular dimension (d.) Size of holes, slots and recesses (15.) What is produced from blast furnace? (a.) Pig iron (b.) Cast iron (c.) Wrought iron (d.) Malleable iron (16.) What is the minimum dimension can measure with telescopic gauge? (a.) 8.0 mm (b.) 12.7 mm (c.) 19.0 mm (d.) 150 mm (17.) Which cast iron has the ability to minimize tool chatter in machine tools? (a.) Grey cast iron (b.) White cast iron (c.) Nodular cast iron (d.) Malleable cast iron (18.) What is the term of the algebraic difference between a size, to its corresponding basic size? (a.) Deviation (b.) Upper deviation (c.) Lower deviation (d.) Actual deviation (19.) What is the upper limit of the component size ? (a.) 0.005 (b.) 0.008 (c.) 19.995 (d.) 20.008 (20.) What is the term used for the relationship exists between two mating parts? (a.) Fit (b.) Limit (c.) Tolerance (d.) Allowance (21.) What is the least count of vernier micrometer? (a.) 0.01 mm (b.) 0.02 mm (c.) 0.001 mm (d.) 0.002 mm (22.) How chipped out scraper can be repaired? (a.) Filing (b.) Lapping (c.) Chiselling (d.) Grinding and honing (23.) Which part of vernier micrometer is marked with vernier scale graduation ? (a.) Anvil (b.) Frame (c.) Thimble (d.) Barrel (24.) Which instrument is used to measure the effective diameter of screw threads? (a.) Screw pitch gauge (b.) Outside micrometer (c.) Screw thread micrometer (d.) Screw thread caliper gauge (25.) What is the lower limit of size, if dimension is stated as ? (a.) 24.85 mm (b.) 24.75 mm (c.) 25.00 mm (d.) 25.021 mm (26.) What is the name of system if the size of the hole is kept constant, shaft is varied? (a.) Bilateral system (b.) Unilateral system (c.) Hole basis system (d.) Shaft basis system (27.) What is the algebraic difference between the actual size and its corresponding basic size? (a.) Deviation (b.) Tolerance (c.) Actual deviation (d.) Upper deviation (28.) Which device is used in conjunction with dial test indicator? (a.) Chuck (b.) Stand (c.) Tool rest (d.) Bench vice (29.) Which scraper is used to scrape small diameter holes and deburing edges of holes? (a.) Flat scraper (b.) Hook scraper (c.) Triangular scraper (d.) Bull-nose scraper (30.) Which surface is used for scraping large bearing surface? (a.) Flat scraper (b.) Hook scraper (c.) Triangular scraper (d.) Bull-nose scraper (31.) What is the difference between maximum limit of size and the minimum limit of size? (a.) Tolerance (b.) Basic size (c.) Limits of size (d.) Upper deviation (32.) Which is grade of tolerance? (a.) Bilateral tolerance (b.) Unilateral tolerance (c.) Fundamental tolerance (d.) Fundamental deviation (33.) What is the maximum limit of size if the basic size of the hole is 25 mm and the deviation is ± 0.2mm? (a.) 25.2 mm (b.) 24.8 mm (c.) 25.02 mm (d.) 24.08 mm (34.) Which term indicates the difference between the maximum limit of size and minimum limit of size? (a.) Deviation (b.) Tolerance (c.) Actual size (d.) Upper deviation (35.) Which type of fit, the tolerance zone of hole is below the tolerance zone of shaft? (a.) Transition fit (b.) Clearance fit (c.) Shrinkage fit (d.) Interference fit (36.) Which term indicates the algebraic difference between the actual size and its corresponding basic size? (a.) Deviation (b.) Actual deviation (c.) Upper deviation (d.) Lower deviation (37.) What is the expression of 30H7/g6? (a.) Fit (b.) Limits (c.) Deviation (d.) Tolerance (38.) What is the lower limit of size in dimension of ? (a.) 19.988 (b.) 20.028 (c.) 20.007 (d.) 19.979 (39.) What is the angle of holding the scrapers for soft metal? (a.) 30° (b.) 60° (c.) 40° (d.) 20° (40.) What is the upper deviation of the component size (a.) 0.005 (b.) 0.008 (c.) 19.995 (d.) 20.008 (41.) What is the lower limit of size, if dimension is stated as in a drawing? (a.) 24.85 mm (b.) 24.75 mm (c.) 24.000 mm (d.) 25.021 mm (42.) Which part indicates the reading of dial test indicates? (a.) Stem (b.) Anvil (c.) Pointer (d.) Plunger (43.) Which scraper is used to scrape the centre portion of large flat surface? (a.) Flat scraper (b.) Hook scraper (c.) Triangle scraper (d.) Bull-nose scraper (44.) Which instrument is used to magnify small variation in sizes by means of pointer on a graduated dial? (a.) Dial test indicator (b.) Inside micrometer (c.) Dial vernier caliper (d.) Vernier micrometer (45.) What is the number of fundamental deviation in the BIS system ? (a.) 25 (b.) 20 (c.) 15 (d.) 26 (46.) How many fundamental tolerance grades are available? (a.) 18 grade (b.) 25 grade (c.) 15 grade (d.) 12 grade (47.) Which precision instrument is used for comparing and determining the variation in the sizes of the component? (a.) Micrometer (b.) Comparators (c.) Dial test indicator (d.) Vernier bevel protector (48.) What mechanism is used in the lever type dial test indicator? (a.) Screw and nut (b.) Rack and pinion (c.) Lever and scroll (d.) Worm and worm wheel (49.) Which comparator is used in mass production? (a.) Optical (b.) Pneumatic (c.) Electronics (d.) Mechanical (50.) Which gauge used to check internal thread of components (a.) Thread ring gauge (b.) Taper ring gauge (c.) Thread plug gauge (d.) Caliper gauge Previous QuestionNext Question Keywords :- ITI Mock , ITI Mock Test, ITI Mock Test NCVT, ITI Mock Test 2020, ITI Mock Test 2021, ITI Mock Test 2022, ITI Mock Test 1st Year, ITI Mock Test 2nd Year, ITI Mock Test PDF Download, ITI Test, ITI Test Paper, ITI Test Questions, ITI Test Book, ITI Test Paper in hindi, ITI Test 2020, ITI Test 2021, ITI Test 2022, ITI Questions Answers, ITI Questions & Answers, ITI Questions & Answers pdf, ITI Question Paper, ITI Questions pdf, ITI Question Paper PDF, ITI Questions Paper 2020, ITI Questions Paper 2021, ITI Questions Paper 2022, ITI Answer Key, ITI Paper Scheme, ITI Paper Date, ITI Paper 2020, ITI Paper 2021, ITI Paper 2022, ITI Previous Year Question Paper, ITI Previous Year Question Paper NCVT, ITI Previous Year Question Paper ED, ITI Previous Year Question Paper Engineering Drawing, ED, Workshop Calculations & Science, ITI Previous Year Question Paper Workshop Calculations & Science, ITI ED Book PDF, ITI ED Drawing, ITI ED Drawing Exaam Paper, ITI Jobs, ITI Form, ITI Form Online, ITI Online Form, ITI Online Form 2022, UP ITI, ITI Uttar Pradesh, ITI Haryana, ITI UK, ITI UttraKhand, UP ITI Result, Uk ITI Result, Haryana ITI Result, MP ITI Result, UP ITI Scholarship, Uk ITI Scholarship, Haryana ITI Scholarship, MP ITI Scholarship, UP ITI Merit List, Uk ITI Merit List, Haryana ITI Merit List, MP ITI Merit List, UP ITI Exam Date, Uk ITI Exam Date, Haryana ITI Exam Date, MP ITI Exam Date, UP ITI Updates, Uk ITI Updates, Haryana ITI Updates, MP ITI Updates, UP ITI Admission, Uk ITI Admission, Haryana ITI Admission, MP ITI Admission If you have any dought in any question. you can comment below, we will reply as soon as possible. and subscribe our Youtube channel & Telegram channel for more updates..

ITI Fitter Trade 50 MCQs Practice Questions – Part 5

Recent Posts

Daily Current Affairs Quiz: 15-December-2024

Daily Current Affairs Quiz: 14-December-2024

Daily Current Affairs Quiz: 13-December-2024

Daily Current Affairs Quiz:12-December-2024

Daily Current Affairs Quiz:11-December-2024

Daily Current Affairs Quiz: 10-December-2024

ITI Fitter Trade 50 MCQs Practice Questions – Part 5

Related Post

Recent Posts

Daily Current Affairs Quiz: 15-December-2024

Daily Current Affairs Quiz: 14-December-2024

Daily Current Affairs Quiz: 13-December-2024

Daily Current Affairs Quiz:12-December-2024

Daily Current Affairs Quiz:11-December-2024

Daily Current Affairs Quiz: 10-December-2024